3.2.3  
CBSAP 
 
NOTE  
Danger of damage to property due to surge voltage. The required lightning protection measures must be taken for this board, see Section 2.1.2 "Lightning Protection".  

Introduction  
The CBSAP board (Central Board Synergy Access Platform) performs all central control and switching functions for HiPath 3800 (see Figure 3-5).

Capacity  
 •   DTMF transmitters: 12
 •   DTMF receivers: 12
 •   Tone generators: 16
 •   Dial tone receivers: 4

Subboards  
The following subboards can be used depending on the application:
 •   CMS clock module (optional)
 •   MMC multimedia card
 •   IMODN integrated modem card new (optional)
 •   LIMS LAN interface module (optional)
Contains two Ethernet (10BaseT) LAN connectors (8-pin RJ45 jacks):
   -   LAN1 (administration via HiPath 3000/5000 Manager E and CTI functions)
   -   LAN2 (not assigned)
 •   Music on hold (optional):
   -   MPPI (Product of BEYERTONE GmbH)
   -   MUSIC (Product of Sound Player GmbH)

V.24 interfaces (9-pin SUB-D plug)  
 •   Service (X50) = for connecting the service PC
 •   Application (X51) = for connecting a printer or application

Switches and indicators  
 •   Reset/reload switch:
   -   Switch pressed < 5 s = Reset activated
   -   Switch pressed > 5 s = Reload activated (Fail LED (red) goes out to indicate that a reload is in progress).
 •   Two LEDs indicating the board status:
   -   Run (green) = signals the current status of the CBSAP board (see Table 12-2)
   -   Fail (red) = error encountered
 •   Two LEDs for displaying the LAN interface status:
   -   LED1:
- Green = 100 Mbps online (link)
- Yellow = 10 Mbps online (link)
- Flashing = active
   -   LED2 (green):
- On = full-duplex (FDX)
- Off = half-duplex

Diagram of CBSAP board  
 Figure 3-5   CBSAP Board (S30810-Q2314-X)
 

Front panel  
 Figure 3-6   CBSAP - Front Panel
 

V.24 interface assignment  

 Table 3-17   CBSAP - V.24 Interface Assignment (SUB-D Plug)
 X50/X51, Pin  
 Signal  
 Description  
 1  
 DCD  
Data carrier detect (not used)  
 2  
 RxD  
Receive data  
 3  
 TxD  
Transmit data  
 4  
 DTR  
Data terminal ready (not used)  
 5  
 0 V  
Ground  
 6  
 DSR  
Data send ready (not used)  
 7  
 RTS  
Request to send  
 8  
 CTS  
Clear to send  
 9  
 RI  
Ring indicator (not used)  

LAN connector assignment via LIMS  

 Table 3-18   CBSAP - LAN Connector Assignment (RJ45 Jack)
 Pin  
 Signal  
 Description  
 1  
 Tx +  
Transmit +  
 2  
 Tx -  
Transmit -  
 3  
 Rx +  
Receive +  
 4  
 -  
Not used  
 5  
 -  
Not used  
 6  
 Rx -  
Receive -  
 7  
 -  
Not used  
 8  
 -  
Not used  

HiPath 3000/5000 V9, Service Documentation, Issue 7   up Top
Disclaimer & Copyright   ID: P31003H3590S100017620   2012-06-25