7.2.3  
Station view: Workpoint Client 
 
Workpoint Client is used to define the parameters for an IP terminal, e.g., the IP address for an H.323 or SIP client.

7.2.3.1  
Area: System Client 

Status message flag  
This flag activates the "keep-alive" mechanism for system telephones.
If Status message is enabled, the status of system telephones can be determined with the HiPath 3000 Manager. When a system telephone is dropped, it is flagged as "inactive" in the CDB after 4 minutes. When the CDB of the system is read, the status can be queried via Settings | Set up station | Subscriber in the Status column. In addition, the status can also be determined via Maintenance | Station Status.
The flag must not be enabled when setting up a system telephone as a home client or when using the "Short-Hold" feature (see Edit PSTN partner). Disabling this flag reduces the message traffic between the HG 1500 boards and the system telephones.

Authentication active flag  
You can define here whether this client requires authentication at the LAN card in order to be used. This is specially relevant in the case of clients who are not on the internal LAN but who are dialing in from the outside.

Password  
If authentication has been activated, enter the password for this client here and confirm your entry by repeating it.

Station type, Mobile, Non-mobile, Mobile blocked  
A Mobile Workpoint Client ( Mobile option) is not assigned to any IP terminal. The call no. of a Mobile Workpoint Client can be used by a subscriber to log on to any IP terminal (that permits this) via the logon procedure (*9419) (provided the option Mobile blocked is not activated).
The feature is only supported from the third station port onwards.  
For a non-mobile Workpoint Client (Non mobile option), by contrast, the call no. is permanently assigned to an IP terminal.
The non-mobile profile is needed for the initial logon (Home Logon) of an IP terminal. Mobile Workpoint Clients may not be used for the home logon. In other words, every WorkPoint Client must be initially registered as a non-mobile Workpoint Client.
If the Mobile blocked option has been activated for a Workpoint Client, a subscriber cannot log on with a mobile Workpoint Client at that IP terminal.
When using a WLAN2 phone, the option Non mobile must be set before registering the WL2 phone with the communication system.

Redundancy Destination  
The redundancy concept takes effect in cases where an application fails. The HFA client is then forwarded to the redundant gatekeeper defined here. In order to define a redundant gatekeeper, the Redundancy Service Application (RSA) must be running in a HiPath 5000 network.

IP Address  
Specify the IP address of the redundant gatekeeper for HFA clients here.
IP Address
Enter the IP address of the standby system.

7.2.3.2  
Area: S0 / H.323 / SIP Client 

Authentication active flag  
You can define here whether the client requires authentication at the LAN card in order to be used. This is specially relevant in the case of clients who are not on the internal LAN but who are dialing in from the outside.

Password  
If authentication has been activated, enter the password for the client here and confirm your entry by repeating it.

UserID  
Enter the user account of the client here.

Realm  
Enter the realm of the client here.

IP Address  
Before you start configuring clients in the administration program, you will need to determine the IP addresses of the client PC involved. In cases where a client is operated at the gatekeeper, this overhead is not required, since the gatekeeper handles the allocation of call numbers to IP addresses. Consequently, the IP address 255.255.255.255 is configured for clients that are operated at the gatekeeper.
The IP address must be unique within the network . Any new IP address to be configured should therefore be "pinged" before it is assigned. If the IP address responds, it should not be assigned again.  

Fixed IP address  
Entering a fixed IP address ensures that only one H.323 client can log on to the system with this IP address. If this flag is activated, the IP address and the call number are verified. If this flag is not activated, only the call number is verified.

SMG register  
Small Media Gateway register. If this flag is activated, this client can also register at an SMG.

Analog adapter connected  
This flag must be activated when an analog station is connected to HiPath 3000 via AP 1120 H.323 and HG 1500. The analog station can make unrestricted use of the HG 1500 features.
If this flag is activated for an AP 1120 SIP, the features are restricted for the analog station. The analog station is able to participate in the "Transfer a call" function passively (accept a transferred call) but not actively (transfer a call).

See also:  
   -   Section 7.1 "Station Selection"
   -   Section 7.2 "Station Parameters"
   -   Section 7.2.1 "Station view: Flags"
   -   Section 7.2.2 "Station view: Activated features"
   -   Section 7.2.4 "Station view: Groups"
   -   Section 7.2.5 "Station view: Forwarding"
   -   Section 8.19.10 "Maintenance | Station Status"
   -   Section 9.2.1 "Subscriber"
   -   Section 9.10.6 "Edit PSTN partner"

HiPath 3000/5000 V8, Manager E, Administrator Documentation, Issue 11   up Top
Disclaimer & Copyright   ID: P31003H3580M1000176A9   2011-03-18