All cables that leave the system cabinet must be attached to the metal back panel using cable ties.

Danger   Be sure to connect the main protective earthing terminal on all system cabinets to the grounding point of the electrical building installation before connecting up the peripherals (for example, potential equalization bus).   The system may only be started (connected to the power supply) if all system cabinets are sealed at the rear with the connection and filler panels provided.

Figure 4-28

HiPath 3800 - Backplane (S30804-Q5392-X) of the Basic Cabinet

Figure 4-29

HiPath 3800 - Connectors and Jacks on the Backplane of the Basic Cabinet

Table 4-6

HiPath 3800 - Assignment of Connectors and Jacks on the Backplane of the Basic Cabinet

Connector	Function
X101 - X105	SIVAPAC connector for connecting peripherals:   CABLUs and open-end cables are used for connection to the MDFU-E or to an external patch panel (see Section 4.1.6.4 "Connecting Peripherals to the SIVAPAC Connector on the Backplane").   Note: The SIVAPAC connectors can have the following connector panels:    •   Connector panels with RJ45 jacks for direct connection of peripherals (see Section 4.1.6.5 "Connecting Peripherals to the Connector Panels with RJ45 Jacks").  •   For U.S. only: Connector panels with CHAMP jack for direct connection of peripherals (see Section 4.1.6.6 "Connecting Peripherals to the Connector Panels with CHAMP Jack (for U.S. only)").  •   Connector panels each with two SIPAC 1 SU connectors for connecting an external main distribution frame or external patch panel using CABLUs (see Section 4.1.6.7 "Connecting Peripherals to Connector Panels with SIPAC 1 SU Connectors"). For selected countries only: PBXXX board: An APPCU adapter (S30807-K5415-X) is used to connect the CAS cable and the DIUN2 connection cable.
X109 - X112
X116	SIVAPAC connectors for picking up the signals from the REALS board.   CABLUs for connection to the MDFU-E (jumper strip for 25 TW):    •   C39195-A7267-A372: 3 m in length, short stripped length for MDFU-E slots 11-21 (see Figure 4-36)  •   C39195-A7267-A373: 3 m in length, long stripped length for MDFU-E slots 1-10 (see Figure 4-36) Open-end cable (24 TW) for connection to an external patch panel:    •   S30267-Z196-A150: 15 m in length  •   S30267-Z196-A250: 25 m in length  •   S30267-Z196-A350: 35 m in length  •   S30267-Z196-A550: 55 m in length  •   S30267-Z196-A950: 95 m in length
X201	68-pin DB68 mini-jack for connecting the cable C39195-Z7611-A10 to the expansion cabinet (for the DBSAP board)
X209	DC port
X211, X212	AC power
X214	10-pin connection for the ring voltage generator RGMOD (for selected countries only)

Figure 4-30

HiPath 3800 - Expansion Cabinet Backplane (S30804-Q5393-X)

Figure 4-31

HiPath 3800 - Connectors and Jacks on the Backplane of the Expansion Cabinet

Table 4-7

HiPath 3800 - Assignment of Connectors and Jacks on the Backplane of the Expansion Cabinet

Connector	Function
X101 - X106	SIVAPAC connector for connecting peripherals:   CABLUs and open-end cables are used for connection to the MDFU-E or to an external patch panel (see Section 4.1.6.4 "Connecting Peripherals to the SIVAPAC Connector on the Backplane").   Note: The SIVAPAC connectors can have the following connector panels:    •   Connector panels with RJ45 jacks for direct connection of peripherals (see Section 4.1.6.5 "Connecting Peripherals to the Connector Panels with RJ45 Jacks").  •   For U.S. only: Connector panels with CHAMP jack for direct connection of peripherals (see Section 4.1.6.6 "Connecting Peripherals to the Connector Panels with CHAMP Jack (for U.S. only)").  •   Connector panels each with two SIPAC 1 SU connectors for connecting an external main distribution frame or external patch panel using CABLUs (see Section 4.1.6.7 "Connecting Peripherals to Connector Panels with SIPAC 1 SU Connectors"). For selected countries only: PBXXX board: An APPCU adapter (S30807-K5415-X) is used to connect the CAS cable and the DIUN2 connection cable.
X109 - X115
X209	DC port
X211	AC power
X214	10-pin connection for the ring voltage generator RGMOD (for selected countries only)
X220 - X223	Connections for plugging in the DBSAP board.   DBSAP has a 68-pin DB68 mini-jack for connecting the cable C39195-Z7611-10 to the basic cabinet (to the jack X201).

To ensure smooth operation, use only shielded cables with a maximum length of 1 m.

Danger   Be sure to connect the main protective earthing terminal on all system cabinets to the grounding point of the electrical building installation before connecting up the peripherals (for example, potential equalization bus).   The system may only be started (connected to the power supply) if all system cabinets are sealed at the rear with the connection and filler panels provided.

If	Then
Slot with    SLCN    SLMA8    SLMO8    STMD3    TM2LP    TMC161    TMDID2	CABLUs for connection between backplane (SIVAPAC connector) and MDFU-E (splitting strip for 16 TW):    •   C39195-A7267-A370: 3 m in length, short stripped length for MDFU-E slots 11-21 (see Figure 4-36)  •   C39195-A7267-A371: 3 m in length, long stripped length for MDFU-E slots 1-10 (see Figure 4-36) CABLU for connection between backplane (SIVAPAC connectors) and external patch panel S30807-K6143-X (SIVAPAC socket terminal strip):    •   S30267-Z333-A20: 2 m in length (refer to Figure 4-42)  •   S30267-Z333-A50: 5 m in length (refer to Figure 4-42) Open-end cable (24 TW) for connection between backplane (SIVAPAC connector) and external patch panel:    •   S30267-Z196-A150: 15 m in length  •   S30267-Z196-A250: 25 m in length  •   S30267-Z196-A350: 35 m in length  •   S30267-Z196-A550: 55 m in length  •   S30267-Z196-A950: 95 m in length
Slot with    SLMA    SLMA21    SLMO2	CABLUs for connection between backplane (SIVAPAC connector) and MDFU-E (jumper strip for 25 TW):    •   C39195-A7267-A372: 3 m in length, short stripped length for MDFU-E slots 11-21 (see Figure 4-36)  •   C39195-A7267-A373: 3 m in length, long stripped length for MDFU-E slots 1-10 (see Figure 4-36) CABLU for connection between backplane (SIVAPAC connectors) and external patch panel S30807-K6143-X (SIVAPAC socket terminal strip):    •   S30267-Z333-A20: 2 m in length (refer to Figure 4-42)  •   S30267-Z333-A50: 5 m in length (refer to Figure 4-42) Open-end cable (24 TW) for connection between backplane (SIVAPAC connector) and external patch panel:    •   S30267-Z196-A150: 15 m in length  •   S30267-Z196-A250: 25 m in length  •   S30267-Z196-A350: 35 m in length  •   S30267-Z196-A550: 55 m in length  •   S30267-Z196-A950: 95 m in length
Slot with    PBXXX1	A CAS cable is connected via an APPCU adapter (S30807-K5415-X).

1for selected countries only 2for U.S. only

After the cable has been connected, the backplane of the basic cabinet and that of the expansion cabinet (if applicable) must be closed with the dummy panels provided (C39165-A7075-C44).

Figure 4-32

HiPath 3800 - Backplane of the Basic Cabinet with Mounted Filler Panels

Figure 4-33

HiPath 3800 - connector panels with RJ45 Jacks

Danger   Be sure to connect the main protective earthing terminal on all system cabinets to the grounding point of the electrical building installation before connecting up the peripherals (for example, potential equalization bus).   The system may only be started (connected to the power supply) if all system cabinets are sealed at the rear with the connection and filler panels provided.

If	Then
Slot with    STMD3	Connector panel with eight RJ45 jacks: S30807-Q6624-X   The RJ45 jacks are configured with four wires. S0 stations can be directly connected (1:1 cable). The receive and send lines should be switched for trunk connections.
Slot with    SLCN    SLMA    SLMA21    SLMA8    SLMO2    SLMO8    TM2LP    TMC161    TMDID2	Connector panel with 24 RJ45 jacks: S30807-Q6622-X   The RJ45 jacks are configured with two wires.
different or no assignment	The backplane sections of other boards and empty board slots must be covered with filler panels.

1for selected countries only 2for U.S. only

Figure 4-34

HiPath 3800 - Connector Panel with CHAMP Jack (for U.S. only)

Danger   Be sure to connect the main protective earthing terminal on all system cabinets to the grounding point of the electrical building installation before connecting up the peripherals (for example, potential equalization bus).   The system may only be started (connected to the power supply) if all system cabinets are sealed at the rear with the connection and filler panels provided.

If	Then
Slot with peripheral card	A cable with CHAP jack should be used to connect to a main distributor frame or external patch panel.
No assignment	The backplane sections with empty board slots must be covered with filler panels.

Figure 4-35

HiPath 3800 - Connector Panel with Two SIPAC 1 SU Connectors (S30807-Q6631-X)

Danger   Be sure to connect the main protective earthing terminal on all system cabinets to the grounding point of the electrical building installation before connecting up the peripherals (for example, potential equalization bus).   The system may only be started (connected to the power supply) if all system cabinets are sealed at the rear with the connection and filler panels provided.

If	Then
Slot with    SLCN    SLMA8    SLMO8    STMD3    TM2LP    TMC161    TMDID2	CABLUs for connection between connector panel (SIPAC 1 SU connectors) and MDFU-E (splitting strip for 16 TW):    •   S30269-Z100-A11: 3 m in length, short stripped length for MDFU-E slots 11-21 (see Figure 4-36)  •   S30269-Z100-A21: 3 m in length, long stripped length for MDFU-E slots 1-10 (see Figure 4-36) CABLU with 16 TW for connection between connector panel (SIPAC 1 SU connectors) and external patch panel S30807-K6143-X (SIVAPAC socket terminal strip):    •   S30267-Z362-A20: 2 m in length (refer to Figure 4-42) Open-end cable (16 TW) for connection between backplane (SIPAC 1 SU connectors) and external patch panel:    •   S30267-Z192-A60: Open-end cable with 16 TW, 6 m in length  •   S30267-Z192-A100: Open-end cable with 16 TW, 10 m in length  •   S30267-Z192-A200: Open-end cable with 16 TW, 20 m in length (Information on the required stripped lengths for open-end cables is provided in Figure 4-47.)
Slot with    SLMA    SLMA21    SLMO2	CABLUs for connection between connector panel (SIPAC 1 SU connectors) and MDFU-E (jumper strip for 25 TW):    •   S30269-Z100-A14: 3 m in length, short stripped length for MDFU-E slots 11-21 (see Figure 4-36)  •   S30269-Z100-A24: 3 m in length, long stripped length for MDFU-E slots 1-10 (see Figure 4-36) CABLU with 24 TW for connection between connector panel (SIPAC 1 SU connectors) and external patch panel S30807-K6143-X (SIVAPAC socket terminal strip):    •   S30267-Z363-A20: 2 m in length (refer to Figure 4-42) Open-end cable (16 TW) for connection between backplane (SIPAC 1 SU connectors) and external patch panel:    •   S30267-Z192-A60: Open-end cable with 16 TW, 6 m in length  •   S30267-Z192-A100: Open-end cable with 16 TW, 10 m in length  •   S30267-Z192-A200: Open-end cable with 16 TW, 20 m in length (Information on the required stripped lengths for open-end cables is provided in Figure 4-47.)
different or no assignment	The backplane sections of other boards and empty board slots must be covered with filler panels.

1for selected countries only 2for U.S. only