NOTE: Danger of damage to property due to surge voltage. The required lightning protection measures must be taken for this board, see Section 2.1.2 "Lightning Protection".

The range of the short S0 bus (up to eight Terminal Equipment Identifiers (TEI)) is limited to approximately 60 m.   If longer cables are required, the S0 bus type must be set to "Long" in HiPath 3000/5000 Manager E developer mode. This provides a range of approximately 160 m. This setting can be made in V5.0 SMR-05 (CV 5) or later.

Figure 3-83

STMD3 (S30810-Q2217-X10) - LEDs in the Front Panel

To ensure sufficient shielding, provide the board with a shielding panel. For information on mounting the shielding panel, see Section 4.1.5.3 "Inserting or Removing Boards".

Table 3-110

STMD3 - LED Statuses

Red LED	Green LED	Status	Action
Off	Off	Board not receiving power or not plugged in correctly.   Board is out of order.	Check plug contact on board.
On	Off	Board is receiving power and board test is in progress.   Board is defective if status remains unchanged (board test unsuccessful).	Replace the board.
		Loadware loading not successfully completed. Board is faulty.	Replace the board.
		Error detected on board.   Board is deactivated (not applicable to errors detected by test loops) or board was deactivated using HiPath 3000/5000 Manager E.	Check whether the board was deactivated using HiPath 3000/5000 Manager E. If not, replace board.
Flashing	Off	Loadware is being loaded.
Off	On	Board test completed successfully. Board is OK (idle state).
Off	Flashing	At least one channel is activated.

Table 3-111

STMD3 - SIVAPAC Connector Assignment on the Backplane

Pair	a-wire1 (tip)	b-wire1 (ring)	SIVAPAC connector	STMD3		MDFU-E	Notes
1	wht/blu		1	1Ea	Basic rate access 1	1a
		blu/wht	23	1Eb		1b
2	wht/ora		3	1Sa		2a
		ora/wht	4	1Sb		2b
3	wht/grn		5	2Ea	Basic rate access 2	3a
		grn/wht	6	2Eb		3b
4	wht/brn		7	2Sa		4a
		brn/wht	8	2Sb		4b
5	wht/gry		9	3Ea	Basic rate access 3	5a
		gry/wht	10	3Eb		5b
6	red/blu		11	3Sa		6a
		blu/red	12	3Sb		6b
7	red/ora		13	4Ea	Basic rate access 4	7a
		ora/red	14	4Eb		7b
8	red/grn		15	4Sa		8a
		grn/red	16	4Sb		8b
9	red/brn		17	5Ea	Basic rate access 5	9a
		brn/red	18	5Eb		9b
10	red/gry		19	5Sa		10a
		gry/red	20	5Sb		10b
11	blk/blu		24	6Ea	Basic rate access 6	11a
		blu/blk	25	6Eb		11b
12	blk/ora		26	6Sa		12a
		ora/blk	27	6Sb		12b
13	blk/grn		29	7Ea	Basic rate access 7	13a
		grn/blk	30	7Eb		13b
14	blk/brn		31	7Sa		14a
		brn/blk	32	7Sb		14b
15	blk/gry		34	8Ea	Basic rate access 8	15a
		gry/blk	35	8Eb		15b
16	yel/blu		37	8Sa		16a
		blu/yel	38	8Sb		16b

1see "Abbreviations for colors" at the start of Section 3.3 "Peripheral Boards".

Table 3-112

STMD3 - Connector Panel Assignment with RJ45 Jacks

RJ45 jack			STMD3		Notes
No.	Subscriber line    Pin	Trunk connection    Pin
1	3	4	1Ea	Basic rate access 1
	6	5	1Eb
	4	3	1Sa
	5	6	1Sb
2	3	4	2Ea	Basic rate access 2
	6	5	2Eb
	4	3	2Sa
	5	6	2Sb
3	3	4	3Ea	Basic rate access 3
	6	5	3Eb
	4	3	3Sa
	5	6	3Sb
4	3	4	4Ea	Basic rate access 4
	6	5	4Eb
	4	3	4Sa
	5	6	4Sb
5	3	4	5Ea	Basic rate access 5
	6	5	5Eb
	4	3	5Sa
	5	6	5Sb
6	3	4	6Ea	Basic rate access 6
	6	5	6Eb
	4	3	6Sa
	5	6	6Sb
7	3	4	7Ea	Basic rate access 7
	6	5	7Eb
	4	3	7Sa
	5	6	7Sb
8	3	4	8Ea	Basic rate access 8
	6	5	8Eb
	4	3	8Sa
	5	6	8Sb

Table 3-113

STMD3 - Connector Panel Assignment with CHAMP Jack (for U.S. only)

CHAMP jack	STMD3		Notes
1	S0, Receive	Basic rate access 1
26	S0, Receive
2	S0, Transmit
27	S0, Transmit
3	S0, Receive	Basic rate access 2
28	S0, Receive
4	S0, Transmit
29	S0, Transmit
5	S0, Receive	Basic rate access 3
30	S0, Receive
6	S0, Transmit
31	S0, Transmit
7	S0, Receive	Basic rate access 4
32	S0, Receive
8	S0, Transmit
33	S0, Transmit
9	S0, Receive	Basic rate access 5
34	S0, Receive
10	S0, Transmit
35	S0, Transmit
11	S0, Receive	Basic rate access 6
36	S0, Receive
12	S0, Transmit
37	S0, Transmit
13	S0, Receive	Basic rate access 7
38	S0, Receive
14	S0, Transmit
39	S0, Transmit
15	S0, Receive	Basic rate access 8
40	S0, Receive
16	S0, Transmit
41	S0, Transmit

Table 3-114

STMD3 - Connector Panel Assignment with SIPAC 1 SU Connectors (Cable for Ports 1 - 16)

Color group	Pair	a-wire1 (tip)	b-wire1 (ring)	SU connector	STMD3		MDFU-E	S0 patch panel, MW8 pin
								Subscriber line	Trunk connection
1	1	wht/blu		19	1Ea	Basic rate access 1	1a	3	4
			blu/wht	39	1Eb		1b	6	5
	2	wht/ora		38	1Sa		2a	4	3
			ora/wht	48	1Sb		2b	5	6
	3	wht/grn		27	2Ea	Basic rate access 2	3a	3	4
			grn/wht	47	2Eb		3b	6	5
	4	wht/brn		16	2Sa		4a	4	3
			brn/wht	46	2Sb		4b	5	6
	5	wht/gry		05	3Ea	Basic rate access 3	5a	3	4
			gry/wht	45	3Eb		5b	6	5
2	6	red/blu		14	3Sa		6a	4	3
			blu/red	44	3Sb		6b	5	6
	7	red/ora		23	4Ea	Basic rate access 4	7a	3	4
			ora/red	43	4Eb		7b	6	5
	8	red/grn		32	4Sa		8a	4	3
			grn/red	42	4Sb		8b	5	6
	9	red/brn		11	5Ea	Basic rate access 5	9a	3	4
			brn/red	31	5Eb		9b	6	5
	10	red/gry		02	5Sa		10a	4	3
			gry/red	22	5Sb		10b	5	6
3	11	blk/blu		13	6Ea	Basic rate access 6	11a	3	4
			blu/blk	33	6Eb		11b	6	5
	12	blk/ora		04	6Sa		12a	4	3
			ora/blk	24	6Sb		12b	5	6
	13	blk/grn		15	7Ea	Basic rate access 7	13a	3	4
			grn/blk	35	7Eb		13b	6	5
	14	blk/brn		06	7Sa		14a	4	3
			brn/blk	26	7Sb		14b	5	6
	15	blk/gry		17	8Ea	Basic rate access 8	15a	3	4
			gry/blk	37	8Eb		15b	6	5
4	16	yel/blu		08	8Sa		16a	4	3
			blu/yel	28	8Sb		16b	5	6

1see "Abbreviations for colors" at the start of Section 3.3 "Peripheral Boards".