3.3.5  
VMNL, IVMN8 
 

Introduction  
The IVMNL and IVMNL8 (Integrated Voice Mail New Large) boards allow you to use the HiPath Xpressions Compact integrated voice mail functionality in HiPath 3800:
 •   IVMNL (S30122-H7688-X) = 24 ports
 •   IVMN8 (S30122-H7688-X100) = 8 ports
Up to 500 mailboxes are available with a total storage capacity of 100 hours. The boards can also be used for Music on Hold and announcements.
HiPath Xpressions Compact supports a central voice mail functionality in a HiPath 3000/5000 network. All stations can use the central voice mail server.  
HiPath Xpressions Compact may be used as a central announcement device in a network system with V6.0 SMR-06 or later.  
Optional administration of HiPath Xpressions Compact via the Ethernet (10/100BaseT) interface in the front panel of the board is also possible.
For detailed information on HiPath Xpressions Compact, startup and administration, see the manual for the product.
Caution  
For thermal reasons the IVMNL board may only be installed in the basic cabinet in a HiPath 3800 19-inch cabinet installation.  
Only one IVMNL or IVMN8 may be installed per HiPath 3800 system.  
In order to avoid inactive IVM channels (due to the slow IVM board boot-up), the following recommendations must be observed:  
 •   IVMNL:
   -   Installing HiPath 3800 (Standalone): The IVMNL board is to be installed in the last slot in the last system cabinet. If possible, the two slots in front should be kept free.
   -   Installing HiPath 3800 (19-Inch Cabinet): The IVMNL board should be installed in the last slot in the basic cabinet. If possible, the two slots in front should be kept free.
 •   IVMN8:
Standalone installation of the HiPath 3800 or 19" cabinet installation of the HiPath 3800: The IVMN8 board should be installed in the last slot in the last system cabinet. If possible, the two slots in front should be kept free.

Front panel  
 Figure 3-39   IVMNL, IVMN8 - Front Panel (S30122-H7688-X -X100)
 
The front of this board does not require an additional plate because EMC shielding has already been achieved by the front panel.

Lockout switch settings  
 •   Pressed = free (default)
 •   Not pressed = locked: existing connections remain active, new connections are locked.
   -   The yellow LED lights up when all connections are ended and the board is effectively locked.
   -   The yellow LED flashes when a lockout request is entered (via lockout switch or software) but at least one call is still active.
To reset the board to the default state, press the lockout switch four times (off-on-off-on) during the LED test at startup. This action cancels the LED test and both LEDs flash for approximately five seconds in confirmation.

LED statuses and their meanings  

 Table 3-42   IVMNL, IVMN8 - LED Statuses
 LED
Yellow  
 LED
Green  
 Meaning  
 Action  
During Startup and Initialization  
 Off  
 Off  
 1  
Boot procedure (lasts approx. 60 s)  
 
 On  
 On  
 2  
LED test (lasts approx. 10 s)  
 
 On  
 Off  
 3  
Lockout switch state signaling by yellow LED (lasts approx. 5 s):  
 •   blocked = On
 •   free = Off
Possibly check if board was deactivated using HiPath 3000/5000 Manager E or lockout switch.  
 Off  
 Flashing
(500/500 ms)  
 Off  
 4  
Hard disk test, application startup (depending on hard disk status, lasts approx. 2 - 9 minutes)  
 
 Off  
 On  
 5a  
Standby mode after successful boot  
 
 On  
 Off  
 5b  
Board locked or board error occurred  
Check whether board was deactivated using HiPath 3000/5000 Manager E or lockout switch.  
Change board if faulty.  
During Operation  
 Off  
 On  
Idle (no call)  
 
 Flashing
(500/500 ms)  
 Off  
At least one active port (call)  
 
 Flashing
(500/500 ms)  
 Flashing
(500/500 ms)  
Lockout switch activated during a call  
 
 On  
 Off  
Board locked or board error occurred  
Check whether board was deactivated using HiPath 3000/5000 Manager E or lockout switch.  
Change board if faulty.  
 Flashing
(100/100 ms)  
 Off  
Upgrade process active  
 

RJ45 jack assignment  

 Table 3-43   IVMNL, IVMN8 - RJ45 Jack Assignment
 Pin  
 Signal  
 Description  
 1  
 Tx +  
Transmit +  
 2  
 Tx -  
Transmit -  
 3  
 Rx +  
Receive +  
 4  
 -  
Not used  
 5  
 -  
Not used  
 6  
 Rx -  
Receive -  
 7  
 -  
Not used  
 8  
 -  
Not used  

HiPath 3000/5000 V8, Service Documentation, Issue 10   up Top
Disclaimer & Copyright   ID: P31003H3580S100017620   2011-01-24