9.2.1 Subscriber

9.2.1	Subscriber

Settings | Setup station | Stations

The Station tab consists of a table, which is divided into the following columns. The values for the call number, DID number and name can be changed by selecting the individual fields.

The table is often not fully visible. In order to see all entries, use the horizontal scroll function or reduce the width of the columns by moving the column separators.

This station status can also be printed via Print / Print Preview.

You can also configure the stations via the new Station view.

Call no. (call number) column

The Call no. column contains the internal call number of the relevant station. This number may contain a maximum of six digits.

When a fax or modem station is deleted (i.e., the call number and DID are deleted), the extension type must also be be reset to the default (standard).

DID (direct inward dialing number) column

The DID number assigned to the corresponding extension is entered in this column. This number may contain a maximum of 11 digits. This is the call number used for DID and CorNet.

When a fax or modem station is deleted (i.e., the call number and DID are deleted), the extension type must also be be reset to the default (standard).

If a call number if modified in this table, the same modifications must be made in Call Management (Settings | Incoming calls).

The tables under Settings | Incoming calls are updated immediately once changes have been saved for the Call no. and DID fields.

If your provider has assigned you various MSNs, you can enter these "CO numbers" in the DID column to define the call allocation. The MSN is entered without the "prefix". An MSN can only be assigned to a single internal call number. If an MSN is to be signaled at multiple internal stations, a group or hunt group call number must be entered. The stations are then assigned to the groups (see Groups/hunt groups).

If you want to unassign the MSN, you can also delete it from the DID column. Please note, however, that a call to an unassigned MSN (CO numbers) will not be signaled or only signaled at the first port at the intercept position.

Name column

The name assigned to the station is entered here. The name can also be entered via the Station view. More details on the name of a station can be found in the station view under Name.

Status column

Can only be changed by physically reconfiguring the communication system.

The status of the relevant station port is displayed in the Status column. If a gray symbol or the * symbol appears in this column, the port (station) is inactive. If a green symbol appears in this column or if the field is empty, the port (station) is inactive.

Cordless base stations with SLUC cards are always shown as inactive, since this call number cannot be reached.

If a mobile phone is involved, the following status indicators are used:

Port active

PP registered

Status display

Meaning

yes

green

yes

red

Board lockswitch set for registered PP.

yellow

PP was automatically logged off by a change to the PIN in the Manager E.

yes

gray

No PP was ever registered on this port.

The status indicated here is that of the port when the customer database is downloaded.

Type column

Can only be changed by physically reconfiguring the communication system.

The type of telephone connected to the station port is automatically specified by the communication system. If a telephone is not connected, No Port is displayed in the column. If an analog telephone is connected, the column entry is "No Fe".

No Port, i.e. no telephone connected

No Fe, i.e. analog telephone connected

System telephone connected

S0 station

Access column

Can only be changed by physically reconfiguring the communication system.

The name, number, slot of the station system board and the type of Workpoint Client (SYS=System, S0) are displayed here. This column also indicates whether the port is a master or a slave.

For an offline-configured database, there are no slave ports with HiPath 37xx. You can assign a slave port to a specific master port by double-clicking the Access field. The result is identical to connecting a slave terminal on the hardware side and then reading the CDB. If a slave port is assigned, you can remove it for both the master port and the slave port by double-clicking the Access field.

CLIP column

If Configurable CLIP is activated, a valid DID number can be specified for each device here (see also Configurable CLIP under Flags). If no CLIP number was specified, the supplied Calling Partner Number is delivered (as before).

CLIP and LIN (Location Identification Number; only in the USA) are mutually exclusive. By default, LIN is activated for the USA and CLIP for all other countries. If CLIP is activated for the USA, LIN is automatically disabled.

LIN column (Location Identification Number; USA only)

When emergency number E911 is set up, a valid DID (direct inward dialing) is entered for each telephone. This number identifies the location of the station from which the emergency call was made. There is no consistency test carried out for this.

LIN and CLIP are mutually exclusive (see also CLIP).

Check button

Ensure that you have not assigned the same station number or DID number to two or more stations by pressing the Check button to initiate a check. If duplicates are found, an error message is displayed together with a list of the duplicates. You can then make appropriate corrections.

When assigning call numbers in the communication system to S0 stations, the closing digits of this number must be unique in relation to all internal call numbers of all other stations (for example: The S0 call number 9553193 conflicts with the station call number 193).

HiPath 3000/5000 V8, Manager E, Administrator Documentation, Issue 10		up

Disclaimer & Copyright	ID: P31003H3580M1000176A9	2011-01-24